On-demand InkJet Printing System
CraftPix CPQ Model
Equipped with 4 print heads. The Second highest speed model following the CPE model.
High Speed Printing Model
CPQ7861
CPQ model equipped with four print heads on its dedicated body, enables high-speed printing next to the CPE model. The alignment time is dramatically reduced by implementation of three CCD cameras. The vast print area covered by the four print heads enables printing on a 22.8 x 17” (580 x 430 mm) substrate in as fast as 11 seconds surpassing CPi. Being equipped with two ink tanks, it is possible to use as a two-color printing model with a 2 head + 2 head configuration.
Dimensions [ unit: inch(mm) ]
Detailed Specifications of
CPQ7861
|
Max. Panel Size
|
31.3 x 25.6” (795 x 651 mm)
|
| Max. Discharge Frequency |
45 kHz
|
|
X-axis Resolution (dpi)
|
360 / 720 / 1080 / 1440
|
|
Y-axis Resolution (dpi)
|
360 / 720 / 1080 / 1440 / 1800 / 2160
|
|
Min. Droplet Size
|
6 pl / 13 pl
|
|
Number of Nozzles
|
4 x 1024 (4096)
|
|
Standard Resolution
|
720 dpi
|
|
Min. Line Width
*1
|
70 µm–90 µm
|
|
Speed
*2
|
22.8 x 17” (580 x 430 mm): 11 seconds
24 x 20” (610 x 510 mm): 11 seconds 30.7 x 24" (780 x 610 mm): 20 seconds |
|
Number of Ink Tank
|
2
|
|
Ink Tank Volume (Max.)
|
1000 ml x 2
|
|
On-Head UV Lamp
*3
|
LED-UV Lamp
|
|
Camera Resolution
|
11.8 x 9.0 mm
|
|
Air Supply: Pressure
|
0.5 MPa
|
|
Air Supply: Volumetric flow rate
|
5.4 ft³/min. (150 ℓ/min.)
|
|
Power Supply
*4
Single Phase AC200–240 V 50/60 Hz |
20 A
|
|
Weight
|
3968 lbs. (1800 kg)
|
*1 Depends on ink
*2 While using UV pinning type ink, speed spec may change according to required UV energy. Print times do not include image alignment, shuttle and load and unload time. Please confirm the printing quality and speed by allowing us to run a benchmark test at MicroCraft.
*3 LED UV lamp to be mounted depends on the ink to be used.
*4
Separate power source for cooling device and vacuum pump is necessary (specifications may be different in some countries). § Replacement of ink requires special training § CraftPix consumables are ink, cleaning fluid, filter, sending fluid tube, UV lamp, array unit, vacuum paper, temperature sensor, heater, etc. § Please contact MicroCraft for detailed specification.
Operating Conditions
70–75°F (21–24°C), 30–70% relative humidity
* Free of moisture, dust (ISO class 7 (FED-STD-209D Class 10,000) clean room or better), vibration, and corrosive gas.
Atmospheric Dew Point: −14°C or below (at 0.7 Mpa, dew point is 15°C or below)
Oil Mist Concentration: 1 mg/㎥ (ANR) or below
Common Specification
| Board Thickness |
0.004 to 0.24" (0.1 - 6.0 mm)
*5
*compatibility for thickness exceeds 0.24" (0.6 mm) is optional
|
| Alignment |
CCD Camera
|
| Monitor |
Touch Screen LCD Monitor
|
| Software | Windows 7 / Windows 8 / Windows 10 |
| Data Input Format | RS274X, RS274D, ODB++, DPF, DXF, BMP *6 , TIFF *6 |
*5 When the vacuum table is used. Figures depend on the board warpage and clamp type. Printing quality may decrease with warpage. Please contact MicroCraft for more precise figures for specific conditions.
*6 Scaling and alignment functions are not usable.
Vacuum Pump*
| Power Supply |
Three Phase AC200 V 10 A 50/60 Hz, AC220 V 10 A 60 Hz
|
| Capacity |
50 Hz: 20.7 ft³/min. (575 ℓ/min.)
60 Hz: 24.7 ft³/min. (685 ℓ/min.)
|
| Air Coupler Size |
RC 3/4
|
| Weight | 187.4lbs. (85 kg) |
* Depends on clamping method
Inquiries about CraftPix series
Please feel free to contact us for questions regarding the machine specs, quotes, inquiries for a brochure from the following phone number or the inquiry form. The equipment seen in the lineup are customizable to address your needs.