On-demand InkJet Printing System
CraftPix CPi Model
Standard model with 2048 nozzles.
Standard Model
CPi6151 / CPi7861
This standard model is equipped with a total of 2048 nozzles that has doubled the maximum discharge frequency compared to the conventional array used in CPK/CPM models. With its capability of changing print resolution in x-direction by 30dpi step, it allows operators to make precise adjustment to their print quality.
High-resolution printing “Type F”
CPi6151F / CPi7861F
NEW
CPi models are available in “Type F”, which is equipped with a high-definition 1776 nozzles print head and a min. droplet size of 3.5pl. Model that combines enhanced basic performance with a higher level print quality.
Standard Model (Super Large Size Model)
CPi11078 / CPi11091 / CPi120110
NEW
CraftPix also comes in Super Large Size Model capable of printing extremely large work size, and this custom model is offered for each of CPi, CPJ, and CPT models. Print speed and quality is equivalent of these models in standard 6151 / 7861 size. This model is also installed with single direction printing with moving print head unit, where it moves front / rear direction.
Detailed Specifications of CPi6151 / CPi6151F
|
|
CPi6151 | CPi6151F |
| Max. Panel Size | 24.6 x 21" (625 x 535 mm) |
24.6 x 21" (625 x 535 mm)
|
| Max. Discharge Frequency | 45 kHz | 80 khZ |
| X-axis Resolution (dpi) | 360 / 720 / 1080 / 1440 | 600 / 900 / 1200 / 1500 / 2400 |
| Y-axis Resolution (dpi) | 720 / 1440 / 2160 | 1200 / 2400 |
| Min. Droplet Size | 6 pl / 13 pl | 3.5 pl |
| Number of Nozzles | 2 x 1024 (2048) | 2 x 1776 (3552) |
| Standard Resolution | 720 dpi | 1200 dpi |
| Min. Line Width *1 |
70 µm–90 µm
|
40 µm–70 µm
|
| Speed *2 |
22.8 x 17" (580 x 430 mm): 17 seconds
24 x 20" (610 x 510 mm): 23 seconds |
22.8 x 17" (580 x 430 mm): 17 seconds
24 x 20" (610 x 510 mm): 27 seconds |
|
|
CPi6151 | CPi6151F |
| Number of Ink Tank | 1 | 1 |
| Ink Tank Volume (Max.) | 1000ml | 1000ml |
| On-Head UV Lamp *3 | Led-UV Lamp |
Led-UV Lamp
|
| Camera Resolution | 8.4 x 6.3 mm | 8.4 x 6.3 mm |
| Air Supply: Pressure | 0.5 MPa | 0.5 MP |
| Air Supply: Volumetric flow rate |
2.7 ft³/min. (75 ℓ/min.)
|
2.7 ft³/min. (75 ℓ/min.)
|
|
Power Supply*4
Single Phase AC200-240V 50/60 Hz
|
15 A | 15 A |
| Weight | 1543 lbs. (700kg) | 1543 lbs. (700kg) |
| Dimensions [ unit: inch (mm) ] |
|
|
*1 Depends on ink
*2 While using UV pinning type ink, speed spec may change according to required UV energy. Print times do not include image alignment, shuttle and load and unload time. Please confirm the printing quality and speed by allowing us to run a benchmark test at MicroCraft.
*3 LED UV lamp to be mounted depends on the ink to be used.
*4
Separate power source for cooling device and vacuum pump is necessary (specifications may be different in some countries). § Replacement of ink requires special training § CraftPix consumables are ink, cleaning fluid, filter, sending fluid tube, UV lamp, array unit, vacuum paper, temperature sensor, heater, etc. § Please contact MicroCraft for detailed specification.
Operating Conditions
70–75°F (21–24°C), 30–70% relative humidity
* Free of moisture, dust (ISO class 7 (FED-STD-209D Class10,000) clean room or better), vibration, and corrosive gas.
Atmospheric Dew Point: −14°C or below (at 0.7 Mpa, dew point is 15°C or below)
Oil Mist Concentration: 1 mg/㎥ (ANR) or below
Detailed Specifications of CPi7861 / CPi7861F
|
|
CPi7861 | CPi7861F |
| Max. Panel Size | 31.3 x 25.6” (795 x 651 mm) |
31.3 x 25.6” (795 x 651 mm)
|
| Max. Discharge Frequency | 45 kHz | 80 khZ |
| X-axis Resolution (dpi) | 360 / 720 / 1080 / 1440 | 600 / 900 / 1200 / 1500 / 2400 |
| Y-axis Resolution (dpi) | 720 / 1440 / 2160 | 1200 / 2400 |
| Min. Droplet Size | 6 pl / 13 pl | 3.5 pl |
| Number of Nozzles | 2 x 1024 (2048) | 2 x 1776 (3552) |
| Standard Resolution | 720 dpi | 1200 dpi |
| Min. Line Width *1 |
70 µm–90 µm
|
40 µm–70 µm
|
| Speed *2 |
22.8 x 17" (580 x 430 mm): 17 seconds
24 x 20" (610 x 510 mm): 23 seconds 30.7 x 24” (780 x 610 mm): 31 seconds |
22.8 x 17" (580 x 430 mm): 17 seconds
24 x 20" (610 x 510 mm): 27 seconds 30.7 x 24” (780 x 610 mm): 31 seconds |
|
|
CPi7861 | CPi7861F |
| Number of Ink Tank | 1 | 1 |
| Ink Tank Volume (Max.) | 1000ml | 1000ml |
| On-Head UV Lamp *3 | Led-UV Lamp |
Led-UV Lamp
|
| Camera Resolution | 8.4 x 6.3 mm | 8.4 x 6.3 mm |
| Air Supply: Pressure | 0.5 MPa | 0.5 MP |
| Air Supply: Volumetric flow rate |
2.7 ft³/min. (75 ℓ/min.)
|
2.7 ft³/min. (75 ℓ/min.)
|
|
Power Supply
*4
Single Phase AC200-240V 50/60 Hz
|
15 A | 15 A |
| Weight | 2205 lbs. (1000 kg) | 2205 lbs. (1000 kg) |
| Dimensions [ unit: inch (mm) ] |
|
|
*1 Depends on ink
*2 While using UV pinning type ink, speed spec may change according to required UV energy. Print times do not include image alignment, shuttle and load and unload time. Please confirm the printing quality and speed by allowing us to run a benchmark test at MicroCraft.
*3 LED UV lamp to be mounted depends on the ink to be used.
*4
Separate power source for cooling device and vacuum pump is necessary (specifications may be different in some countries). § Replacement of ink requires special training § CraftPix consumables are ink, cleaning fluid, filter, sending fluid tube, UV lamp, array unit, vacuum paper, temperature sensor, heater, etc. § Please contact MicroCraft for detailed specification.
Operating Conditions
70–75°F (21–24°C), 30–70% relative humidity
* Free of moisture, dust (ISO class 7 (FED-STD-209D Class10,000) clean room or better), vibration, and corrosive gas.
Atmospheric Dew Point: −14°C or below (at 0.7 Mpa, dew point is 15°C or below)
Oil Mist Concentration: 1 mg/㎥ (ANR) or below
Detailed Specifications of CPi11078 / CPi11091 / CPi120110
|
|
CPi11078
|
CPi11091
|
CPi120110
|
|
Max. Panel Size
|
45 x 31.1” (1142 x 790 mm)
|
45 x 35.8” (1142 x 910 mm)
|
48 x 44” (1220 x 1120 mm)
|
|
Max. Discharge Frequency
|
45 kHz
|
45 kHz
|
45 kHz
|
|
X-axis Resolution (dpi)
|
360 / 720 / 1080 / 1440
|
360 / 720 / 1080 / 1440
|
360 / 720 / 1080 / 1440
|
|
Y-axis Resolution (dpi)
|
720 / 1440 / 2160
|
720 / 1440 / 2160
|
720 / 1440 / 2160
|
|
Min. Droplet Size
|
6 pl / 13 pl
|
6 pl / 13 pl
|
6 pl / 13 pl
|
|
Number of Nozzle
|
2 x 1024 (2048)
|
2 x 1024 (2048)
|
2 x 1024 (2048)
|
|
Standard Resolution
|
720 dpi
|
720 dpi
|
720 dpi
|
|
Min. Line Width
*1
|
70 µm–90 µm
|
70 µm–90 µm
|
70 µm–90 µm
|
|
Speed
*2
|
22.8 x 17” (580 x 430 mm): 17 seconds 24 x 20” (610 x 510 mm): 23 seconds 30.7 x 24” (780 x 610 mm): 31 seconds 43.3 x 30.7” (1100 x 780 mm): 58 seconds |
22.8 x17” (580 x 430 mm): 17 seconds 24 x 20” (610 x 510 mm): 23 seconds 30.7 x 24” (780 x 610 mm): 31 seconds 43.3 x 30.7” (1100 x 780 mm): 58 seconds |
22.8 x17” (580 x 430 mm): 17 seconds 24 x 20” (610 x 510 mm): 23 seconds 30.7 x 24” (780 x 610 mm): 31 seconds
43.3 x 30.7” (1100 x 780 mm): 58 seconds
|
|
|
CPi11078
|
CPi11091
|
CPi120110
|
|
Number of Ink Tank
|
1 | 1 | 1 |
|
Ink Tank Volume (Max.)
|
1000 ml
|
1000 ml
|
1000 ml
|
|
On-Head UV Lamp
*3
|
LED-UV lamp
|
LED-UV lamp
|
LED-UV lamp
|
|
Camera Resolution
|
8.4 x 6.3 mm
|
8.4 x 6.3 mm
|
8.4 x 6.3 mm
|
|
Air Supply: Pressure
|
0.5 MPa
|
0.5 MPa
|
0.5 MPa
|
|
Air Supply: Volumetric flow rate
|
2.7 ft³/min. (75 ℓ/min.)
|
2.7 ft³/min. (75 ℓ/min.)
|
2.7 ft³/min. (75 ℓ/min.)
|
|
Power Supply
*4
Three Phase AC200–230 V 50/60 Hz |
20 A
|
20 A
|
20 A
|
|
Weight
|
3748 lbs. (1700 kg)
|
4850 lbs. (2200 kg)
|
5952 lbs. (2700 kg)
|
|
Dimensions [ unit: inch(mm) ]
|
|
|
|
*1 Depends on ink
*2 While using UV pinning type ink, speed spec may change according to required UV energy. Print times do not include image alignment, shuttle and load and unload time. Please confirm the printing quality and speed by allowing us to run a benchmark test at MicroCraft.
*3 LED UV lamp to be mounted depends on the ink to be used.
*4
Separate power source for cooling device and vacuum pump is necessary (specifications may be different in some countries). § Replacement of ink requires special training § CraftPix consumables are ink, cleaning fluid, filter, sending fluid tube, UV lamp, array unit, vacuum paper, temperature sensor, heater, etc. § Please contact MicroCraft for detailed specification.
Operating Conditions
70–75°F (21–24°C), 30–70% relative humidity
* Free of moisture, dust (ISO class 7 (FED-STD-209D Class10,000) clean room or better), vibration, and corrosive gas.
Atmospheric Dew Point: −14°C or below (at 0.7 Mpa, dew point is 15°C or below)
Oil Mist Concentration: 1 mg/㎥ (ANR) or below
Common Specification
| Board Thickness |
0.004 to 0.24" (0.1 - 6.0 mm)
*5
*compatibility for thickness exceeds 0.24" (0.6 mm) is optional
|
| Alignment |
CCD Camera
|
| Monitor |
Touch Screen LCD Monitor
|
| Software | Windows 7 / Windows 8 / Windows 10 |
| Data Input Format | RS274X, RS274D, ODB++, DPF, DXF, BMP *6 , TIFF *6 |
*5 When the vacuum table is used. Figures depend on the board warpage and clamp type. Printing quality may decrease with warpage. Please contact MicroCraft for more precise figures for specific conditions.
*6 Scaling and alignment functions are not usable.
Vacuum Pump*
| Power Supply |
Three Phase AC200 V 10 A 50/60 Hz, AC220 V 10 A 60 Hz
|
| Capacity |
50 Hz: 20.7 ft³/min. (575 ℓ/min.)
60 Hz: 24.7 ft³/min. (685 ℓ/min.)
|
| Air Coupler Size |
RC 3/4
|
| Weight | 187.4lbs. (85 kg) |
* Depends on clamping method
Inquiries about CraftPix series
Please feel free to contact us for questions regarding the machine specs, quotes, inquiries for a brochure from the following phone number or the inquiry form. The equipment seen in the lineup are customizable to address your needs.